What is an NVRthe box your CCTV footage actually lives on
The cameras get the attention, but the recorder decides how many days you keep, whether a power cut leaves a gap and whether a burglar can walk off with the evidence. Here is what an NVR does, how it differs from a DVR, and what to check before you buy one.
The quick answer
An NVR (network video recorder) is the box that records IP cameras. The cameras send compressed video over network cable, and the NVR writes it to its hard drives and plays it back to your phone. A DVR does the same job for older analogue cameras on coax. Whichever you have, the recorder is where the footage lives, so its drives, its location and its power supply decide whether the evidence is still there when you need it.
What this page covers
- What an NVR does, and how it differs from a DVR.
- Why the channel count is the least useful number on the box.
- PoE ports on the recorder, and the power budget nobody checks.
- Which hard drive to fit, and how to size it.
- Where to put the recorder so a burglar or a power cut does not take the footage.
- NVR against cloud recording, and which UniFi console is the NVR.
Four places CCTV can record to
The last column is the one that matters: each option loses footage in a different way.
| Where it records | Cameras it takes | Where the footage sits | What loses you footage |
|---|---|---|---|
| NVR (network video recorder) | IP cameras on network cable, often powered down the same cable | On the recorder's own hard drives, in your building | Theft of the box, a dead drive, a power cut with no battery backup |
| DVR (digital video recorder) | Analogue cameras on coaxial cable, powered separately | On the recorder's own hard drives, in your building | As an NVR, plus older camera technology and a coax-only upgrade path |
| Memory card in each camera | Each camera records to itself | Spread across every camera, one card each | Small capacity, and the card leaves with the camera if it is pulled off the wall |
| Cloud recording | Mostly Wi-Fi cameras and doorbells | On the provider's servers, reached over your internet line | Internet outage, upload limits, and a fee that runs for as long as you want footage |
NVR (network video recorder)
- Cameras it takes
- IP cameras on network cable, often powered down the same cable
- Where the footage sits
- On the recorder's own hard drives, in your building
- What loses you footage
- Theft of the box, a dead drive, a power cut with no battery backup
DVR (digital video recorder)
- Cameras it takes
- Analogue cameras on coaxial cable, powered separately
- Where the footage sits
- On the recorder's own hard drives, in your building
- What loses you footage
- As an NVR, plus older camera technology and a coax-only upgrade path
Memory card in each camera
- Cameras it takes
- Each camera records to itself
- Where the footage sits
- Spread across every camera, one card each
- What loses you footage
- Small capacity, and the card leaves with the camera if it is pulled off the wall
Cloud recording
- Cameras it takes
- Mostly Wi-Fi cameras and doorbells
- Where the footage sits
- On the provider's servers, reached over your internet line
- What loses you footage
- Internet outage, upload limits, and a fee that runs for as long as you want footage
By the Doberman install team · UniFi CCTV designers & installers, England · Last reviewed November 2026
By the Doberman install team
UniFi CCTV designers & installers, England
Last reviewed November 2026
What an NVR actually does all day
An NVR does three jobs. It receives a video stream from every camera, writes those streams to its hard drives, and lets you find and watch what it recorded. Everything else on the spec sheet is a detail of one of those three.
The word that matters is network. An IP camera is a small computer. It takes the picture from its own sensor, compresses it, and sends it down a network cable as data. The NVR never sees raw video. It gets finished streams, which is why an NVR can sit on the same network as everything else in the building and why one cable to each camera can carry both the picture and the power.
On the recording side, it keeps writing until the drives are full, then overwrites the oldest footage first. That is why the number of days you keep is set by the drives and the cameras together, not by a setting you choose, and why we wrote a whole page on how long CCTV footage lasts before it overwrites.
On the playback side, the recorder is what your phone talks to. On a UniFi system, Ubiquiti says all video recordings are stored locally on the console, such as the UNVR or Cloud Gateway Max, and that it cannot view, store or access your video streams at any point. Your phone connects to the recorder over an encrypted link, and the footage comes from the box in your building rather than from a server somewhere else. We cover the app side in viewing your CCTV on your phone.
NVR or DVR: which one you have
Look at the cable going into the back of the recorder. A round coaxial cable with a twist-on BNC plug means a DVR. A network cable with a clip-in RJ45 plug, the same as on a broadband router, means an NVR.
The real difference is where the video is turned into a file. A DVR takes analogue signals from its cameras and does the encoding itself. An NVR takes streams the cameras have already encoded. That one fact explains most of what follows. A DVR system needs a separate power supply to each camera, because coax only carries the picture. An NVR system can power cameras down the network cable using PoE, which we explain in PoE vs Wi-Fi CCTV.
Modern DVRs have closed some of the gap. They take HD analogue formats over the same coax, and many are hybrid, sometimes sold as XVRs. One major manufacturer's 8-channel hybrid recorder, for example, has eight BNC inputs that detect HD-CVI, AHD, HD-TVI and older CVBS cameras automatically, records analogue cameras at up to 5 MP, and takes up to 12 IP cameras if you convert its analogue channels. That makes a DVR the cheaper way to modernise a building that already has coax in the walls and no easy route for new cable.
The trade-off is the ceiling. An IP camera brings its own processing, so features like person and vehicle detection can happen on the camera. Ubiquiti, for example, says its G4, G5 and AI Series cameras perform person and vehicle detection on the device. On a DVR system, the cameras are simpler and the recorder carries all of it. If you are starting from bare walls, there is little reason to choose a DVR today. If you have sound coax already run, it is worth an honest look before ripping it out.
Channels are the least useful number on the box
Recorders are sold as 4, 8, 16 or 32 channel, and one channel is one camera. It is the first number people check and the one least likely to be what stops the system working.
Two other limits bite first. The recorder can only take in so much video per second, usually quoted as incoming bandwidth in megabits per second. Eight 4K cameras send far more data than eight 1080p cameras, so a recorder can have a free channel and still be unable to record another camera at full quality. The other limit is storage: every extra camera divides the same terabytes by one more, so your days of footage drop each time you add one.
A typical 8-channel PoE recorder from one major manufacturer shows how this reads on a spec sheet. It takes 160 Mbps of incoming video with its AI features off and 80 Mbps with them on, so switching on person detection halves what it can record. It can show eight 1080p cameras live at once but only two 8 MP ones. And it has one drive bay, so there is no protection if that drive fails. None of that is in the words "8 channel" on the box.
UniFi is a useful example because it does not sell by channel at all. Ubiquiti rates each recorder by resolution instead. The four-bay UNVR handles 60 HD cameras, 30 2K cameras or 18 4K cameras. Read that as a budget rather than a count: one 4K camera uses roughly the capacity of three and a third HD ones, so a mix of resolutions uses the budget up in proportion.
For sizing, a sensible order of questions is:
- How many cameras will be fitted on day one, and how many could you want later? A drive, a garden office or a side return often gets added in year two.
- At what resolution? That sets how quickly they eat the recorder's capacity.
- How many days of footage do you need? That sets the drives, and the CCTV storage calculator will work it out for you.
If you are not sure how many cameras the property needs in the first place, we have worked that out for a three-bedroom house and for a small shop.
PoE ports on the recorder, and the power budget nobody checks
Some NVRs have PoE ports on the back, so each camera plugs straight into the recorder and gets power and data down one cable. It is tidy, and for a small system it saves buying a separate switch. Two numbers decide whether it works: the number of ports and the total power the recorder can hand out across them.
Those two numbers do not always agree. Take the UNVR Instant, the UniFi recorder with built-in PoE. Ubiquiti lists six PoE ports, up to 15.4 W on any one port, and a 40 W budget across all of them. Now put cameras on it:
- Six G5 Bullets, which Ubiquiti rates at 4 W each at most, draw up to 24 W. Well inside the budget.
- Six G6 Bullets, rated at up to 9.9 W each, could draw 59.4 W. That is almost 20 W over the budget, even though every camera is under the per-port limit.
- Four G6 Bullets come to 39.6 W, which fits, just.
Other brands work the same way. The 8-port recorder above has a 72 W total budget and up to 25.5 W on a single port. Two cameras drawing that much use 51 W between them, and a third would take the recorder past its 72 W total with five ports still empty.
So six ports does not mean six cameras. It means six cameras of the right kind. The fix, when the budget runs out, is a separate PoE switch with its own power supply, and that is how the larger UniFi recorders work anyway: the UNVR and UNVR Pro have no PoE ports at all, and the cameras are powered from a switch.
If you are planning a system yourself, add up the maximum power of every camera from its spec sheet before you buy the recorder. Use the maximum, not the typical figure, because the budget has to cover every camera at its busiest at the same time.
Would rather someone else did the power sums?
Tell us how many cameras you want and where. We will design the recorder, switch and power budget around them, with room for the cameras you add later.
Which hard drive goes in a CCTV recorder
A drive rated for surveillance or enterprise use. A recorder writes around the clock, and an ordinary desktop drive is not built for it. One manufacturer rates its standard desktop drive for 2,400 powered-on hours a year. A year has 8,760. Its surveillance drive, from the same catalogue, is rated for workloads of up to 180 TB a year and sold for continuous 24/7 running.
It is worth doing the sum for your own system. Our storage calculator assumes a 4K camera recording around the clock writes about 77 GB a day. Over a year that is roughly 28 TB per camera. Six such cameras come to about 170 TB a year of writing, close to that 180 TB rating. Eight come to about 226 TB, past it. Those are writes alone, before anyone plays anything back.
For a UniFi recorder, Ubiquiti publishes its own requirements:
- 3.5 inch hard drives (UNVR, UNVR Pro, Dream Machine Pro, UNVR Instant): a UniFi-branded drive in 8, 16 or 24 TB, or a CMR drive of 1 TB or more at 7,200 rpm. Ubiquiti says 5,400 rpm drives are not recommended in multi-bay consoles running RAID 5, 6 or 10.
- 2.5 inch and NVMe SSDs (Cloud Key Gen2 Plus, Cloud Gateway Max): for Protect, the SSD must have DRAM cache and an endurance of at least 0.3 drive writes per day.
- MicroSD (Dream Router, Dream Wall): at least 128 GB.
CMR and SMR are two ways of laying data on the platters. SMR overlaps its tracks to fit more on, and Seagate says it is best suited to data that is written once and read occasionally, such as backups and archives. A recorder is the opposite: it overwrites its oldest footage all day. Ubiquiti's 8 TB UniFi drive, for scale, is rated for 550 TB a year and a mean time between failures of 2 million hours.
Sizing comes down to cameras, resolution and days. The storage calculator does the arithmetic. Two things to add to its answer:
- Drive protection costs capacity. On a UNVR, Ubiquiti's Basic Protection uses RAID 5, which survives one failed drive and leaves 67 to 75 per cent of the raw space usable. Four 8 TB drives give about 24 TB, not 32.
- A single-bay recorder has no protection. One drive, one failure, and the footage on it is gone. That is the honest weakness of the smaller consoles.
Worked through the same calculator assumption, five 4K cameras on a Cloud Gateway Max with a 2 TB SSD keep about five days of continuous footage. Six 4K cameras on a UNVR Instant with an 8 TB drive keep about 17. Recording on motion only stretches both, at a cost we cover in continuous vs motion-only recording. How a drive fails, and what a service visit checks, is in CCTV maintenance and servicing, so we will not repeat it here.
Where to put the recorder so the footage survives
Somewhere locked, out of sight, dry, within its temperature range and on battery backup. Where the recorder goes gets less thought than any other part of the system, and it is the one decision that can make every camera useless at once.
Out of sight and locked. A recorder on a shelf in the hall is one a burglar can see, unplug and carry out, along with every second of footage of them doing it. Government guidance on police requirements for CCTV says the recorded video should be retained in a secure environment, and gives a system in a locked room as an example. For a home, the government's domestic CCTV guidance adds that you must keep the recordings secure and keep access to them to a minimum. A locked cupboard, a comms cabinet or a loft hatch nobody would think to open all do the job.
Inside its temperature range. Read the spec sheet rather than guessing. Ubiquiti rates the UNVR and UNVR Pro for -5 to 40 degrees C, the UNVR Instant for 0 to 40, and the UNVR for humidity of 5 to 95 per cent, non-condensing. An unheated garage in January and a boarded loft in a heatwave are the two places to check first. A recorder also makes heat, so a sealed cupboard with no airflow can push it past its own limit on a warm day.
On a UPS. A UPS (uninterruptible power supply) is a battery that keeps the recorder and its switch running through a power cut. Without one, the system records nothing from the moment the power drops, which is a gap a burglar who knows where the fuse board is can create on purpose. Size it to the load: Ubiquiti's own UPS Tower is rated for about 2 minutes at full load and 7 minutes at half load, so a small UPS covers a flicker, not an outage. A lightly loaded UPS lasts longer. The rack-mounted UNVR also has a second DC power input for a redundant power supply.
Near the network. The recorder needs a cable to your router for remote viewing, and a cable from the switch to every camera. Putting it next to the router, or running one good cable between the two, keeps the cable routes short. When the broadband drops, a local recorder keeps recording regardless, which we explain in what happens to CCTV footage when the internet goes down.
With the clock right. The same police guidance says the system clock should be set correctly and maintained, taking account of GMT and BST, because time and date are critical to an investigation. A recorder that loses power and comes back with the wrong time can make good footage hard to use.
Not sure where the recorder should live?
Send us the property type and roughly where the router and fuse board are. We will say where the recorder, switch and battery backup should go before anything is drilled.
NVR or cloud: where your footage should live
For a wired system covering a whole property, a local recorder, with cloud as an optional backup for the clips that matter. Cloud recording on its own suits a doorbell or a single Wi-Fi camera, and it has three costs: every camera uploads over your broadband, nothing is stored when the internet is down, and the fee runs for as long as you want to keep footage. We cover the subscription question in can CCTV work without a subscription and the storage question in is my CCTV footage stored in the cloud.
The one real weakness of a local recorder is that it is a single box. If it is stolen, burned or flooded, the footage goes with it. That is the argument for hiding it, and it is also where an off-site copy earns its keep.
UniFi now does both. By default, Ubiquiti says, there is no cloud backup of your video: everything stays on the console. If you want an off-site copy, its optional UniFi Cloud Storage can archive recordings for the cameras and detection types you choose, such as people or vehicles, and Ubiquiti says archived recordings stay accessible even when the console is offline. It is billed by the terabyte actually used, at $5 per TB a month with a $5 minimum, and stored with Backblaze in the US East region. That is worth knowing if you care where your data sits. Archiving event clips rather than every hour of every camera keeps the amount small.
The UniFi version: which console is the NVR
In a UniFi system the NVR is whichever console runs UniFi Protect. Ubiquiti calls them consoles because some of them also run the rest of the network. The Cloud Gateway Max and the Dream Machine Pro are routers that record. The UNVR range only records. Which one makes sense comes down to how many cameras, at what resolution, and whether you want more than one drive.
| UniFi console | Recording storage | Cameras it manages | PoE ports for cameras |
|---|---|---|---|
| Cloud Gateway Max | One NVMe SSD slot, up to 2 TB | 15 HD, 8 2K or 5 4K | None |
| Cloud Key Gen2 Plus | One 2.5 inch bay, 1 TB pre-installed | 24 HD, 14 2K or 8 4K | None (it can be powered by PoE itself) |
| Dream Machine Pro | One 3.5 inch bay | 24 HD, 14 2K or 8 4K | None |
| UNVR Instant | One 3.5 inch bay | 15 HD, 8 2K or 6 4K | 6 ports, 40 W in total, 15.4 W per port |
| UNVR | Four 2.5 or 3.5 inch bays | 60 HD, 30 2K or 18 4K | None |
| UNVR Pro | Seven 2.5 or 3.5 inch bays | 70 HD, 35 2K or 24 4K | None |
Cloud Gateway Max
- Recording storage
- One NVMe SSD slot, up to 2 TB
- Cameras it manages
- 15 HD, 8 2K or 5 4K
- PoE ports for cameras
- None
Cloud Key Gen2 Plus
- Recording storage
- One 2.5 inch bay, 1 TB pre-installed
- Cameras it manages
- 24 HD, 14 2K or 8 4K
- PoE ports for cameras
- None (it can be powered by PoE itself)
Dream Machine Pro
- Recording storage
- One 3.5 inch bay
- Cameras it manages
- 24 HD, 14 2K or 8 4K
- PoE ports for cameras
- None
UNVR Instant
- Recording storage
- One 3.5 inch bay
- Cameras it manages
- 15 HD, 8 2K or 6 4K
- PoE ports for cameras
- 6 ports, 40 W in total, 15.4 W per port
UNVR
- Recording storage
- Four 2.5 or 3.5 inch bays
- Cameras it manages
- 60 HD, 30 2K or 18 4K
- PoE ports for cameras
- None
UNVR Pro
- Recording storage
- Seven 2.5 or 3.5 inch bays
- Cameras it manages
- 70 HD, 35 2K or 24 4K
- PoE ports for cameras
- None
Figures from each model's page on Ubiquiti's tech specs site. The camera numbers are alternatives, not a total: a mix of resolutions uses the capacity up in proportion.
A few things the table shows that are easy to miss. The small consoles cap out quickly at 4K: five cameras on a Cloud Gateway Max, eight on a Dream Machine Pro. Only the UNVR Instant has PoE for cameras, and its 40 W budget is the limit covered above. And only the multi-bay UNVR and UNVR Pro can protect footage against a dead drive.
On whether Protect runs without a drive: the recordings have to go somewhere, and Ubiquiti lists storage for every console that records. The Cloud Gateway Ultra, the smaller gateway below the Max, has no recording storage slot on its spec sheet and lists only the Network application. If you are buying a gateway with cameras in mind, check for a drive bay or SSD slot first. For what the app itself does, see UniFi Protect explained, and for how the cameras compare, see types of CCTV camera. What a full install costs, recorder included, is in CCTV installation cost.
About this page
Where this comes from
Choosing a recorder means reading spec sheets for the numbers the box does not print on the front: power budget, drive requirements and operating range.
Sources
UniFi console, camera and drive figures come from Ubiquiti's tech specs pages for the UNVR, UNVR Pro, UNVR Instant, Cloud Gateway Max and the other models named. Drive requirements are from Ubiquiti's storage requirements and compatibility article, RAID figures from its storage protection article and cloud archiving from its UniFi Cloud Storage article. The desktop and surveillance drive comparison uses Seagate's SkyHawk and BarraCuda specifications. The 8-channel PoE recorder and the hybrid DVR examples are Dahua's NVR4108HS-8P-4KS3 and XVR5108HS-I3 (the second is now discontinued, and is used only as an example of the type). Placement rules are from GOV.UK's police requirements for CCTV systems and domestic CCTV guidance. Naming those companies is a citation of published figures, not a brand recommendation.
What we have deliberately not said
We have not given recorder prices, because they change by the month and by retailer. The days-of-footage examples use our storage calculator's own assumption of about 77 GB per 4K camera per day, which is an average, not a figure Ubiquiti publishes. Real bitrates vary with the scene and the settings.
Common questions
What is an NVR?
An NVR, or network video recorder, is the box that records IP cameras. Each camera turns its own picture into compressed video and sends it over a network cable, and the NVR receives those streams, writes them to its hard drives and serves them to your phone or screen when you want to watch. It is where the footage actually lives, so it decides how many days you keep, how quickly you can find an incident and whether a power cut or a burglar takes the evidence with it.
What is the difference between an NVR and a DVR?
Where the video gets turned into a file. A DVR, or digital video recorder, takes analogue cameras over coaxial cable and does the encoding inside the recorder. An NVR takes IP cameras over network cable, and each camera has already encoded its own video before it arrives. In practice a DVR goes with older coax systems and an NVR goes with modern network cameras, which can also be powered down the same cable.
Do I need an NVR?
You need something to record to, and for a wired IP system that is an NVR or a console that does the same job. The alternatives are a memory card in each camera or a cloud subscription. Both work for a doorbell or a single camera. For a whole property, a recorder keeps every camera in one place, records whether or not the internet is up and does not charge a monthly fee for the footage.
How many channels do I need on an NVR?
Count the cameras you will fit, then add the ones you will want later, because adding channels usually means replacing the recorder. Check bandwidth and storage as well as the channel number. UniFi does not sell by channel at all: its recorders are rated by camera resolution, so the 4-bay UNVR handles 60 HD cameras, 30 2K cameras or 18 4K cameras. Higher resolution uses up capacity faster.
Which hard drive should I use for CCTV?
A drive rated for surveillance or enterprise use, never a desktop drive. Desktop drives can be rated for as little as 2,400 powered-on hours a year, while a recorder runs for 8,760. For UniFi, Ubiquiti asks for a CMR drive of 1 TB or more spinning at 7,200 rpm, and says 5,400 rpm drives are not recommended in multi-drive recorders running RAID. Its own UniFi drives come in 8, 16 and 24 TB and the 8 TB is rated for 550 TB of workload a year.
Where should I put my NVR?
Somewhere locked, out of sight, dry and inside the temperature range on its spec sheet, on a battery backup if you can. Government guidance says recorded video should be kept in a secure environment and gives a locked room as an example. Most UniFi recorders are rated to 40 degrees C at the top end. Avoid the hallway shelf by the front door: a recorder a burglar can see is one they can carry off.
Can UniFi Protect be used without a hard drive?
Not for recording. Ubiquiti says all Protect recordings are stored locally on the console, so every console that runs Protect has somewhere to put them: a hard drive bay, a pre-fitted SSD, an NVMe slot or, on the smallest gateways, a microSD card of at least 128 GB. The Cloud Gateway Ultra has no recording storage slot and lists only the Network application. Ubiquiti does offer optional cloud archiving of event clips, but that is a backup on top of local storage, not a replacement for it.
Which HDD should I use for UniFi Protect?
Either a UniFi-branded drive (8, 16 or 24 TB) or a CMR drive of at least 1 TB spinning at 7,200 rpm, which is what Ubiquiti specifies for its rack-mounted consoles and the UNVR Instant. Avoid SMR drives and 5,400 rpm drives in a multi-drive recorder. If you use a 2.5 inch SSD or an NVMe SSD instead, Ubiquiti requires one with DRAM cache and an endurance of at least 0.3 drive writes per day for Protect.
Want a recorder sized for the cameras you actually need?
Answer a few quick questions and we will quote from your answers. If anything needs a look in person, we arrange a survey first.
