Doberman

CCTV camera not workingfind the fault in the right order

Count how many cameras have stopped before you touch anything: it tells you which part failed. Then work from the cable outwards, with the factory reset last, not first.

The quick answer

Before touching anything, count how many cameras have stopped. If it is one camera, the fault is on the part only that camera uses: its cable, its switch port or the camera. If it is all of them, it is something they share: the recorder, the PoE switch or the power to both. Then work from the cable outwards: power, cable, port, network address, settings. A factory reset comes last, because on UniFi kit it can leave you with a camera Protect still lists but cannot reach.

What this page covers

  • How the pattern of the failure tells you which part has gone.
  • Offline cameras, no signal and black screens: power and cable first.
  • The PoE power sum most systems never get checked against.
  • Offline only on your phone, which is usually not a camera fault at all.
  • Live view working but nothing recorded, and playback that fails.
  • Recorder drive failures and how to swap a drive without losing footage.
  • Night picture faults, how to reset safely, and where an engineer earns the call-out.

Read the pattern first

What failed, and how much of it, narrows the search before you pick up a screwdriver.

One camera down, the rest fine

What it points to
That camera, its cable, its switch port or its power
First check
Swap the cable, try a different switch port

Several cameras down together

What it points to
Something they share: one switch, one power supply, one cable route
First check
Find what those cameras have in common

Every camera down at once

What it points to
The recorder, the main PoE switch, or the mains to them
First check
Check the switch and recorder have power

Fine at home, offline on your phone

What it points to
Remote access, not the cameras
First check
Test on home Wi-Fi, turn off any VPN

Live picture fine, nothing recorded

What it points to
Recording settings, the drive, or the recorder at its limit
First check
Check recording mode and drive health

Fine by day, poor or glaring at night

What it points to
Infrared bouncing back, a dirty or loose cover
First check
Look at what is near the camera

By the Doberman install team

UniFi CCTV designers & installers, England

Last reviewed November 2026

One camera or all of them: why the count matters most

A CCTV system is a chain. Each camera has its own cable and its own switch port. After that, everything is shared: the PoE switch that powers the cameras, the recorder that saves the footage, the mains supply and the internet connection your phone uses to look in.

So the number of cameras that have gone tells you where in the chain to look. One camera down while the others carry on means the shared parts are working, because they are working for everyone else. Ignore the recorder and look at that one camera's cable, port and power. Two or three going together usually share something: the same switch, the same cable route through the loft, the same outdoor power supply. Every camera going at once points at the switch, the recorder or the power to them.

The other two patterns catch people out. If the cameras work on the home network but not on your phone when you are out, the cameras are probably fine and the fault is in remote access. If the live picture is fine but there is nothing to play back, the problem is recording or storage, not the camera. Both have their own sections below.

It also helps to ask what changed. A power cut, a new router, a firmware update, building work or a storm the night before will often point straight at the cause.

Offline, no signal or a black screen: power and cable first

A camera that shows offline, "no signal" or a black tile is usually not getting power, not getting a connection, or both. On a wired PoE camera, one cable carries power and data, so a single bad cable or port kills both at once.

Ubiquiti's own order for an offline UniFi device is the right order for any system:

  1. Check for signs of power. On the switch, the port the camera plugs into has lights. On UniFi switches, a PoE light that is off means no power is going down that port, and a link light that is off means no connection.
  2. Replace the cable. Ubiquiti calls damaged cables one of the most common reasons devices do not get power. Use a short patch lead you know works, at the switch end first, since that is the easy end to reach.
  3. Try a different switch port, or a different PoE adapter if the camera is powered by one, to rule out a damaged port. A blinking light on a UniFi PoE adapter can mean the device is not connected properly or something is wrong with the cable.
  4. Check it has an IP address. A UniFi device stuck on the 192.168.1.20 fallback address has not been given one by your network. Plugging a laptop into the same cable and port is a neat test: if the laptop also gets no address, or one starting 169.254, the network is the problem, not the camera.
  5. Then, and only then, reset and re-adopt the camera, covered further down. If a UniFi camera is still within its warranty and nothing above brings it back, Ubiquiti handles replacements through its RMA portal.

Older analogue systems, where each camera runs a coax cable and a separate power supply to a DVR, use the same swap-and-test logic. Try a spare power supply you know works. Plug the camera into a different input on the recorder. Connect it near the recorder on a short cable. If it works close up and not on the real cable, the cable run is the fault. If it still shows nothing with known-good power and cable, the camera has gone.

Wi-Fi cameras add one more link that can break. Ubiquiti notes that a weak Wi-Fi signal to a camera affects recording quality and leaves gaps in the footage. That is one of the reasons we covered in PoE vs Wi-Fi CCTV.

The PoE power sum nobody checks

A PoE switch has two limits: how much power each port can deliver, and how much it can give out in total. Ubiquiti is blunt about the second one. Its total, which it calls PoE availability, "must be greater than the sum of all device power requirements to prevent instability or failure."

That is a sum you can do yourself, because Ubiquiti publishes the power each camera draws and the total each switch range can supply.

Device (Ubiquiti published figure)Power
G5 Flex camera4 W
G5 Bullet camera5 W
G5 Dome or AI Bullet camera7.7 W
AI 360 camera8.6 W
G5 Pro camera10 W
AI Pro camera11 W
PTZ Ultra camera42.9 W
UniFi Lite switch, total PoE available45 to 52 W

Four AI Pro cameras at 11 W each come to 44 W, which is already at or near the top of a Lite switch's 45 to 52 W before anything else is plugged in. Add an access point and you are over. One PTZ Ultra at 42.9 W needs more than an ordinary PoE+ port can hand a device, which Ubiquiti lists as 25.5 W, so it needs a PoE++ port.

A switch that is over budget does not usually fail cleanly. Cameras drop off and come back, or the last one plugged in never powers up, which looks exactly like a faulty camera. If your cameras go offline at odd times, or a new camera broke an old one, add up the watts before you buy a replacement.

One more trap: not all PoE is the same. Standard PoE negotiates the voltage with the camera. Passive PoE, which UniFi and UISP PoE adapters use, always outputs power without asking, and Ubiquiti warns that different PoE types may not work with each other. Never plug a passive adapter's output into a laptop or printer.

Checks point to the cable or the switch?

If a known-good patch lead fixes nothing and the fault sits in a cable run through a wall or loft, or the switch cannot power every camera on it, that is the point to have it looked at. Tell us what you have found and we will quote for the fix.

Cable faults hide in the bit you cannot see

When a camera works on a short test lead but not on its real cable, the run itself is the fault. Two things are worth knowing before anyone starts pulling cable.

Length. Network cable, Cat5 up to Cat6a, is good for runs up to 100 metres, and that includes powering a PoE camera at the far end. Past that, the run needs splitting with equipment closer to the camera.

What the cable is made of. Cheap cable is often copper-clad aluminium, aluminium wire with a copper coating. One UK CCTV supplier's cabling notes put it plainly: networks using it will never fully meet the Cat5e standard, and it has around 40 per cent higher resistance, which is bad for PoE. More resistance means more voltage lost along the run, so a long run of cheap cable can leave a PoE camera short of power. The fix is full-spec, pure copper cable.

Outdoors, the other usual suspect is the joint behind the camera, where water gets in. We covered that in weatherproofing outdoor CCTV, so we will not repeat it here.

Offline in the app, fine at home

If the cameras play perfectly on your home Wi-Fi and fail on your phone when you are out, the cameras and recorder are working. What has broken is the route from your phone to the recorder. Ubiquiti's checks for UniFi Protect:

  • Test from another phone or browser, and on a different network, to see whether it is one device or everything.
  • Turn off any VPN or privacy app. Ubiquiti says these can interfere with WebRTC, the connection Protect relies on, and suggests turning off private DNS too, especially on Android.
  • Check status.ui.com, which shows whether any UniFi services are down. If they are, nothing at your end will fix it.
  • Check the internet at the house. Ubiquiti says networks below 2.5 Mbps may struggle.
  • On the home network, type the recorder's IP address into a browser to connect to it directly. If that works, the system is fine.
  • Make sure the app is up to date and the user account has remote access permission.

What the recorder keeps doing while your internet is down is explained in what happens to CCTV footage when the internet goes down. How the Protect app and recorder fit together is in UniFi Protect explained.

Live picture works, nothing is recorded

This is the fault people find out about at the worst time, after an incident, because a live picture looks like proof the system works. Government guidance on police requirements for CCTV makes the point directly: view the recorded video, not the live screen, to judge how a system is performing. Check in this order.

The recording mode. In UniFi Protect each camera is set to Always, Detection Only or Never, under Devices, then the camera, then Recording Mode. A camera set to Detection Only records nothing while nothing moves, which is normal. A camera set to Never records nothing at all. Schedules under Settings, Recordings can also limit recording to certain hours. If you are unsure which mode suits you, we weighed them up in continuous vs motion-only recording.

The drive. No working drive, no recordings. The drive health status is the next section.

The recorder's camera limit. Protect shows how many cameras your console can handle and warns when you go over. Ubiquiti says those limits are there so the system can give good playback, fast loading and, above all, not miss recordings. Busy users, lots of live view tiles and the drive's health all push a console towards its limit. As an example, Ubiquiti puts the Dream Router at 5 HD cameras, 2 at 2K or 1 at 4K.

Retention. If recordings exist but older ones have vanished sooner than you expected, the system is probably overwriting on purpose. That is covered in how long CCTV footage lasts before it overwrites, and the CCTV storage calculator shows how much drive a given number of days needs.

Playback that fails or shows the wrong time

Check where you are watching from first. Away from home, Protect plays recordings in lower quality so they run smoothly on a weak connection, while the full-quality copy stays on the recorder. Grainy remote playback is not proof the recording is grainy. Watch the same clip at home before deciding anything.

Slow loading and buffering on a computer can come from the computer itself. Ubiquiti suggests watching fewer cameras at once if the processor is running near flat out.

If clips play but the times are wrong, the recorder clock is out. That matters more than it sounds. Police guidance says the clock should be set correctly and kept right, taking account of GMT and BST, because time and date are critical to an investigation. A clip an hour out after the clocks change is a clip that is hard to rely on. Our page on exporting CCTV footage for the police covers what else they need from it.

When the recorder drive is the fault

The drive in the recorder writes footage around the clock, and it is the part that tells you it is failing if you look. In a UniFi console, open the storage settings and read the drive status:

  • Drive Failure Detected means early signs of failure, such as bad sectors or errors reported by the drive's own SMART checks. Ubiquiti strongly recommends replacing it as soon as possible.
  • Drive at Risk of Failure means a high risk of failure. Ubiquiti says replace it immediately.
  • UniFi Data Found means the drive was used in another UniFi console before, and may need restoring or reformatting.

Before you swap a drive, export any recordings you want to keep, because Ubiquiti warns that all recordings on the disk will be lost. Most UniFi consoles let you pull the drive out while they are running. The exceptions are the CloudKey+ and Cloud Gateways with M.2 storage, which must be powered down first. On a recorder with several drives, replace a failed drive before an at-risk one, one at a time, and let the storage finish repairing in between. For the replacement, Ubiquiti specifies a 1 TB or larger CMR drive at 7,200 RPM for its 3.5 inch bays.

The CloudKey+ has a catch. It runs entirely off its drive, so a new drive means a new database, and every camera then shows "Managed by Other". Restoring from a backup fixes it. Without a backup, every camera has to be reset and adopted again.

Why drives wear out on a different clock from cameras is in how long CCTV cameras last, and what the recorder is actually doing is in what is an NVR.

Recorder drive failing, or the recorder itself gone?

A drive swap can be straightforward, but a dead recorder, a CloudKey+ with no backup or a system already over its camera limit usually means rethinking the recorder. Tell us what the storage screen says and how many cameras you have, and we will quote.

Fine by day, wrong at night

A camera that is sharp in daylight and washed out, hazy or glaring after dark is usually bouncing its own infrared light back into the lens. Ubiquiti lists the causes:

  • Too close to a wall or ceiling. Cameras with infrared should sit at least 60 cm from neighbouring walls and the ceiling, or the reflected light causes glare. A camera tucked tight under a soffit is the one to check.
  • Dirt or fingerprints on the lens or cover. Clean with lens wipes, a lens cloth and cleaning solution, or a soft cloth and rubbing alcohol under 70 per cent.
  • Water droplets on a dome cover, which scatter the infrared. Wipe the outside with a lens cloth.
  • A dome cover not locked in place, which reflects infrared straight back into the lens. Line up the marks and turn it until the seal is hidden.
  • A damaged rubber seal around the lens, which lets infrared leak in and distort the picture.

A night picture that has slowly got darker over the years is a different problem: infrared LEDs fade with age, which we cover in how long CCTV cameras last. What a camera can see in the dark to begin with is in does CCTV work in the dark.

Restart, then reset, and know what a reset really does

"Try a factory reset" is the most common advice online and the one most likely to make things worse. A restart and a reset are different things.

A restart is safe and should come first. For a PoE camera, unplug its cable at the switch for a moment and plug it back in. For the recorder or console, restart it from its settings where you can rather than pulling the plug, because Ubiquiti lists avoiding unexpected shutdowns as one way to look after drive health.

A factory reset wipes the camera's settings, and on UniFi kit there are three things worth knowing first:

  • The physical reset button does not remove the camera from Protect. You can end up with a reset camera that Protect still lists as its own. If the camera is still reachable, the clean way to reset it is Unmanage, in the camera's Manage settings in Protect, which removes it and restores factory settings in one go.
  • Timing matters. Ubiquiti says the button is held for 5 to 10 seconds depending on the device, with the device kept powered throughout. Too short and it only reboots. Too long and it goes into recovery mode.
  • Recovery mode is a last resort, not a stronger reset. On a camera it is done by holding the button while plugging the PoE cable back in, and Ubiquiti warns the camera then reboots to an older firmware.

If you reset the console itself, every camera will show "Managed by Other", because each one still thinks it belongs to the old setup. Ubiquiti's fixes are to restore the console from a backup or reset each camera and adopt it again. Taking a backup before you change anything saves the second option.

Where the DIY checks stop and an engineer makes sense

Everything above, apart from reaching the camera itself, can be done from the switch, the recorder and the app. That covers most faults: a lead, a port, a setting, a remote-access problem. The point where it becomes a job is when the checks have found the fault and the fix is physical:

  • The camera works on a test lead but not on its real cable, and the run is in a wall, loft or underground.
  • The PoE sum does not add up and the switch needs replacing or a second one adding.
  • A camera needs reaching up a ladder you are not comfortable on, or re-mounting away from a wall.
  • The drive is reporting failure, the recorder will not start, or the system is over its camera limit.
  • A camera has been through every check and is simply dead.

Doing the checks first is still worth it. You know which part failed, which makes any quote for the fix quicker and more accurate. To stop the same faults coming back, scheduled checks are covered in CCTV maintenance and servicing, and what we install is on our services page.

About this page

Where this comes from

The fault-finding order, PoE figures, reset behaviour, drive statuses and night-mode causes come from Ubiquiti's help centre: troubleshooting offline devices, device connectivity, PoE availability and modes, resetting to factory defaults, drive and storage health, replacing storage, supported camera limits, camera connectivity and night mode, all read in November 2026. The cable figures are from a UK CCTV supplier's published cabling notes, and the recording and clock points from GOV.UK police requirements for CCTV systems. The PoE sums are our arithmetic on Ubiquiti's published figures.

What we have deliberately not said

We have not given Wi-Fi signal-strength targets, camera light meanings or repair prices, because we could not find a manufacturer or UK source we were happy to stand behind for them. Ubiquiti's status light article covers its switches and access points, not its cameras, so we have only described the switch and PoE adapter lights.

Disclosure

We install Ubiquiti UniFi CCTV, so we benefit when a fault ends in a visit. That is why the free checks come first on this page, and why most of them need nothing more than a spare cable and the app.

Common questions

Why is one of my CCTV cameras not working when the rest are fine?

Because the fault is almost certainly on the part only that camera uses: its cable, its switch port, its power or the camera itself. The recorder, the switch and the internet are shared, and they are clearly working for the others. Swap in a known-good cable and move the camera to a different switch port first. Ubiquiti names damaged cables as one of the most common reasons a device gets no power.

Why have all my cameras stopped working at once?

When every camera goes together, look at what they share: the recorder, the PoE switch that powers them, the mains supply to both, or your internet connection if you only noticed it on your phone. Check the switch has power and its port lights are on, then check the recorder, then check whether the cameras still work on the home network. A single camera fault does not take out the rest.

How do I get my CCTV back online?

Work from the cable outwards. Check the camera has power, swap the network cable, try a different switch port, then check the camera is getting an IP address. On UniFi kit, a device sitting on the 192.168.1.20 fallback address has not been given an address by your network. Only after all of that is a factory reset and re-adoption worth trying, and Ubiquiti puts it last in its own order too.

Why is my CCTV camera showing no signal or a black screen?

No signal nearly always means no power or no connection reaching the recorder, so start with the power supply and the cable at both ends. The quickest test is to swap things for parts you know work: a spare power supply, a short cable, a different recorder input. If the camera still shows nothing with known-good power and cable, the camera is the likely fault.

Why is my CCTV camera not recording any footage?

A live picture does not prove anything is being saved. Check the recording mode first: UniFi Protect cameras can be set to Always, Detection Only or Never, and a schedule can switch recording off at certain times. Then check the drive health status in the recorder, and whether the recorder is over its recommended camera limit, which Ubiquiti says exists partly so you are not missing recordings.

Why is my CCTV playback not working?

Test it on the home network before blaming the recorder. Remote viewing depends on your internet, and Ubiquiti notes that a VPN or private DNS on your phone can break the connection Protect uses. Away from home, Protect plays recordings in lower quality for smoother playback while still storing them in full quality. If playback shows the wrong times, check the recorder clock: police guidance says it must be kept right for GMT and BST.

How do I reset my CCTV camera?

Restart before you reset. A restart is unplugging the camera power for a moment. A factory reset wipes its settings, and on UniFi kit the physical reset button does not remove the camera from Protect, so it can end up listed but unreachable. The clean way to reset a UniFi camera that is still reachable is Unmanage in Protect. Hold the button too briefly and it only reboots; hold it too long and it enters recovery mode.

When should I call an engineer instead of fixing it myself?

Once the checks point somewhere you cannot easily reach or test: a cable run inside a wall or roof space, a camera up a ladder, a switch that cannot power everything on it, or a recorder drive reporting failure. Those are the jobs where the fault is now known and the fix is physical. The checks on this page are worth doing first because they tell you, and anyone you call, exactly which part has failed.

Found the fault but cannot reach it?

Tell us which camera, what the checks showed and what the system is, and we will quote for the repair or the replacement.